Weider Home Gym WEBE15210 User Manual

Model No. WEBE15210  
Serial No.  
Write the serial number in the  
space above for future reference.  
USER’S MANUAL  
Serial Number Decal (Under Seat)  
QUESTIONS?  
As a manufacturer, we are com-  
mitted to providing complete  
customer satisfaction. If you  
have questions, or if there are  
missing parts, we will guarantee  
complete satisfaction through  
direct assistance from our factory.  
TO AVOID UNNECESSARY  
DELAYS, PLEASE CALL DIRECT  
TO OUR TOLL-FREE CUSTOMER  
HOT LINE. The trained techni-  
cians on our customer hot line  
will provide immediate assis-  
tance, free of charge to you.  
CUSTOMER HOT LINE:  
1-800-999-3756  
Mon.–Fri., 6 a.m.–6 p.m. MST  
CAUTION  
Read all precautions and instruc-  
tions in this manual before  
using this equipment. Save this  
manual for future reference.  
Visit our website at  
new products, prizes,  
fitness tips, and much more!  
 
IMPORTANT PRECAUTIONS  
WARNING:  
To reduce the risk of serious injury, read the following important precautions  
before using the weight bench.  
1. Read all instructions in this manual before  
using the weight bench. Use the weight  
bench only as described in this manual.  
10. Do not use a barbell that is longer than six  
feet with the weight bench.  
11. When you put weight on the weight rests,  
make sure you put at least ten pounds on the  
leg lever to balance the weight bench.  
2. The weight bench is intended for home use  
only. Do not use the weight bench in any  
commercial, rental, or institutional setting.  
12. When you are using the leg lever, place a  
barbell with the same amount of weight on  
the weight rests to balance the bench.  
3. It is the responsibility of the owner to ensure  
that all users of the weight bench are ade-  
quately informed of all precautions.  
13. When adjusting the position of the backrest,  
make sure that the backrest adjustment knob  
is fully inserted through the backrest bracket.  
4. Use the weight bench only on a level surface.  
Cover the floor beneath the weight bench to  
protect the floor.  
14. Make sure that the large adjustment knobs  
are inserted completely and tightened into  
the uprights before beginning any exercise.  
5. Make sure all parts are properly tightened  
each time you use the weight bench. Replace  
any worn parts immediately.  
15. Always set both weight rests and both  
weight spotters at the same height.  
6. Keep children under the age of 12 and pets  
away from the weight bench at all times.  
16. The weight bench is designed to support a  
maximum of 560 pounds, including the user,  
a barbell, and weights. Do not place more  
than 310 pounds, including a barbell and  
weights, on the weight rests. Do not place  
more than 150 pounds on the leg lever.  
7. Always wear athletic shoes for foot protec-  
tion while exercising.  
8. Keep hands and feet away from moving parts.  
9. Always keep an equal amount of weight on  
each end of your barbell when you are using  
it. When adding or removing weights, always  
keep some weight on both ends of the bar-  
bell to prevent the barbell from tipping. Note:  
The weight bench does not include a barbell  
or weights.  
17. Always exercise with a partner. When you  
are performing bench press exercises, your  
partner should stand behind you to catch the  
barbell if you cannot complete a repetition.  
18. If you feel pain or dizziness while exercising,  
stop immediately and begin cooling down.  
WARNING:  
Before beginning this or any exercise program, consult your physician. This  
is especially important for persons over the age of 35 or persons with pre-existing health problems.  
Read all instructions before using. ICON assumes no responsibility for personal injury or property  
damage sustained by or through the use of this product.  
3
 
BEFORE YOU BEGIN  
Thank you for selecting the WEIDER® PRO 425 weight Service Department toll-free at 1-800-999-3756,  
bench. The versatile WEIDER® PRO 425 weight bench Monday through Friday, 6 a.m. until 6 p.m. Mountain  
is designed to be used with your own weight set (not  
included) to develop every major muscle group of the  
body. Whether your goal is a shapely figure, dramatic  
increase in muscle size and strength, or a healthier  
cardiovascular system, the WEIDER® PRO 425 will  
help you to achieve the specific results you want.  
Time (excluding holidays). To help us assist you,  
please note the product model number and serial  
number before calling. The model number is  
WEBE15210. The serial number can be found on a  
decal attached to the weight bench (see the front  
cover of this manual).  
For your benefit, read this manual carefully before  
using the WEIDER® PRO 425 weight bench. If you  
have additional questions, please call our Customer  
Before reading further, please look at the drawing  
below and familiarize yourself with the parts that are  
labeled.  
Weight Rests  
Upright  
Adjustment  
Knob  
Backrest  
Weight  
Spotter  
Leg Lever  
Weight Tube  
Backrest Bracket  
Seat  
4
 
PART IDENTIFICATION CHART  
This chart is provided to help you identify the small parts used in assembly. The number in parentheses below  
each part refers to the key number of the part from the PART LIST on page 14 of this manual. Important: Some  
parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags,  
check to see if it has been pre-assembled.  
M6 x 50mm Bolt (39)  
M10 Nylon Locknut (35)  
M10 Washer (27)  
M8 x 55mm Carriage Bolt (40)  
M10 x 65mm Bolt (36)  
M8 Nylon Locknut (42)  
M6 Washer (19)  
M10 x 65mm Carriage Bolt (41)  
M10 x 78mm Bolt (28)  
M6 x 16mm Bolt (31)  
M10 x 95mm Bolt (34)  
M10 x 100mm Bolt (38)  
M10 x 140mm Bolt (37)  
12.5mm Spacer (33)  
5
 
ASSEMBLY  
Place all parts in a cleared area and remove the  
packing materials. Do not dispose of the packing  
materials until assembly is completed.  
Make Things Easier for Yourself  
This manual is designed to ensure that the  
weight bench can be assembled successfully  
by anyone. Most people find that by setting  
aside plenty of time, assembly will go smoothly.  
The following tools (not included) are required  
for assembly:  
• Two adjustable wrenches  
• One rubber mallet  
Before beginning assembly, carefully read the  
following information and instructions:  
• One standard screwdriver  
Assembly requires two people.  
• One Phillips screwdriver  
For help identifying small parts, use the PART  
IDENTIFICATION CHART on page 5.  
• Lubricant, such as grease or petroleum jelly,  
and soapy water.  
Tighten all parts as you assemble them, unless  
instructed to do otherwise.  
Assembly will be more convenient if you have a  
socket set, a set of open-end or closed-end  
wrenches, or a set of ratchet wrenches.  
As you assemble the weight bench, make sure all  
parts are oriented as shown in the drawings.  
1. Before assembling this weight bench, be sure  
that you have read and understand the infor-  
mation in the box above.  
1
Press two 75mm x 50mm Inner Caps (20) into the  
ends of an Upright Stabilizer (5).  
Attach an Upright (4) to the Upright Stabilizer (5)  
with two M10 x 65mm Carriage Bolts (41) and  
two M10 Nylon Locknuts (35). Note: There are  
indents around the holes on one side of the  
Upright Stabilizers; this side must be on the  
bottom.  
Adjustment  
Holes  
4
4
Assemble the other Upright (4) and Upright  
Stabilizer (5) in the same manner.  
Do not tighten the M10 Nylon Locknuts (35) yet.  
35  
Orient the Uprights (4) with the adjustment holes  
on the outside, as shown.  
35  
20  
5
20  
20  
5
41  
20  
41  
6
 
2. Position the Crossbar (3) between the two  
Uprights (4). Note: Make sure the decal on the  
Crossbar is in the position shown. Attach the  
Crossbar to each Upright with four M10 x 95mm  
Bolts (34), two Support Plates (21), and four M10  
Nylon Locknuts (35). Do not tighten the Nylon  
Locknuts yet.  
2
Holes  
35  
Decal  
35  
21  
4
3
34  
21  
34  
3. Attach the Frame (1) to the Crossbar (3) with two  
M10 x 95mm Bolts (34) and two M10 Nylon  
Locknuts (35). Do not tighten the Nylon  
Locknuts yet.  
3
35  
Press two 8mm Bushings (32) into the indicated  
locations on the Frame (1).  
34  
3
32  
20  
Press a 75mm x 50mm Inner Cap (20) into the  
Frame (1).  
1
32  
4. Press two 50mm Square Inner Caps (22) into the  
Front Stabilizer (2).  
4
1
35  
Attach the Front Stabilizer (2) to the Frame (1)  
with two M10 x 65mm Bolts (36), two M10  
Washers (27), and two M10 Nylon Locknuts (35).  
2
22  
Tighten the M10 Nylon Locknuts (34) used in  
steps 1-4.  
27  
8
36  
22  
5. Press four 20mm x 40mm Inner Caps (43) into  
the Backrest Frames (10). Orient the Backrest  
Frames as shown. Note: The indents in the  
Backrest Frames must be on top.  
5
Attach the Backrest Bracket (9) to the Backrest  
Frames (10) with four M8 x 55mm Carriage Bolts  
(40) and four M8 Nylon Locknuts (42). Do not  
tighten the Nylon Locknuts yet.  
40  
43  
Indent  
10  
19  
Attach the Backrest (8) to the Backrest Frames  
(10) with four M6 x 50mm Bolts (39) and four M6  
Washers (19). Do not tighten the Bolts yet.The  
Backrest must be oriented as shown.  
39  
42  
43  
19  
39  
9
42  
7
 
6. Screw the Backrest Adjustment Knob (30) into the  
Frame (1). Pull the Knob out as far as it will go  
and lower the Backrest Bracket (9) between the  
Bench Frame. Snap the Knob into an adjustment  
hole in the Backrest Bracket.  
6
8
30  
35  
Lubricate an M10 x 140mm Bolt (37). Attach the  
indicated set of holes in the Backrest Frames (10)  
and the two Plastic Plates (26) to the Bench  
Frame (1) with the Bolt, two M10 Washers (27),  
and an M10 Nylon Locknut (35). Note: The warn-  
ing decals on the Plastic Plates must face  
away from the bench. Do not overtighten the  
M10 Nylon Locknut; the Backrest (8) must be  
able to pivot easily.  
27  
10  
Hole  
26  
27  
1
9
26  
37  
Decal  
Adjustment Hole  
Lubricate  
7
7. Press the 40mm x 50mm Inner Cap (45) into the  
Seat Frame (6). Press six 8mm Bushings (32) into  
the Seat Frame and the Backrest Frames (10) .  
45  
33  
33  
32  
32  
35  
Attach the Seat Bracket (14) to the Seat Frame  
(6) with an M10 x 78mm Bolt (28) and an M10  
Nylon Locknut (35).  
6
32  
28  
10  
37  
Attach the Seat Bracket (14) to the Frame (1) with  
an M10 x 100mm Bolt (38) and an M10 Nylon  
Locknut (35).  
35  
14  
32  
26  
38  
Lubricate  
Lubricate an M10 x 140mm Bolt (37). Attach the  
bottom set of holes in both the Backrest Frames  
(10) and the two Plastic Plates (26), and two  
12.5mm Spacers (33), to the Seat Frame (6) with  
the Bolt and an M10 Nylon Locknut (35). Do not  
overtighten the M10 Nylon Locknut; the  
Backrest (8) must be able to pivot easily.  
1
8
6
32  
Tighten the M8 Nylon Locknuts (42) used in  
step 5.  
13  
29  
8. Press two 8mm Bushings (32) into the Leg Lever  
Bracket (13).  
Attach the Leg Lever Bracket (13) to the Seat  
Frame (6) with the Small Adjustment Knob (29).  
9
35  
13  
22  
9. Press three 50mm Square Inner Caps (22) into  
the Leg Lever (15). Press a 50mm Round Inner  
Cap (44) into the weight tube.  
15  
Lubricate an M10 x 78mm Bolt (28). Attach the  
Leg Lever (15) to the Leg Lever Bracket (13) with  
the Bolt and an M10 Nylon Locknut (35). Do not  
overtighten the Nylon Locknut; the Leg Lever  
must pivot freely.  
28  
22  
44  
22  
Weight  
Tube  
8
 
10. Press four 19mm Round Inner Caps (24) into the  
ends of the two Pad Tubes (25).  
10  
24  
23  
15  
Insert the Pad Tubes (25) into the holes in the  
Leg Lever (15). Slide two Foam Pads (23) onto  
each Pad Tube.  
23  
23  
24  
25  
23  
11. Attach the Seat (7) to the bracket on the Seat  
Frame (6) using two M6 x 16mm Bolts (31). Attach  
the other end of the Seat to the Seat Frame with  
an M6 Washer (19) and an M6 x 50mm Bolt (39).  
11  
7
6
31  
19  
39  
12. Press a Square Bushing (16) into the top and bot-  
tom of a Weight Rest (12) and a Weight Spotter  
(11). Screw a Large Adjustment Knob (18) into the  
Weight Rest and the Weight Spotter.  
12  
16  
12  
Pull the Large Adjustment Knob (18) in the Weight  
Spotter (11) out as far as it will go. Slide the  
Weight Spotter over an Upright (4). Snap the  
Knob into one of the lower adjustment holes in the  
Upright. Turn the Knob clockwise until tight. Attach  
a Weight Rest (12) to the Upright in the same  
manner. Press an Upright Cap (17) into the top of  
the Upright.  
18  
16  
11  
18  
Repeat this step with the other Upright (4).  
16  
Note: Make sure both Weight Rests (12) and  
both Weight Spotters (11) are set at the same  
height.  
17  
4
13. Make sure that all parts are properly tightened  
before you use the weight bench. The use of  
all remaining parts will be explained in ADJUST-  
MENTS on page 10.  
Adjustment Hole  
9
 
ADJUSTMENTS  
The weight bench is designed to be used with your own weight set (not included). The steps below explain how  
the weight bench can be adjusted. See EXERCISE GUIDELINES on page 11 for important exercise information  
and refer to the accompanying exercise guide to see the correct form for several exercises.  
Make sure all parts are properly tightened each time you use the weight bench. Replace any worn parts immediate-  
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.  
ADJUSTING THE BACKREST  
8
The Backrest (8) can be used in eight different posi-  
tions. To adjust the Backrest, hold the Backrest up  
and pull the Backrest Adjustment Knob (30) out as far  
as it will go. Move the Backrest to the desired posi-  
tion and insert the Knob into an adjustment hole in  
the Backrest Bracket (9).  
15  
30  
WARNING:  
When adjusting the  
9
position of the Backrest (8), first remove all  
weight from the weight tube on the Leg Lever  
(15). Make sure that the Backrest Adjustment  
Knob (30) is fully inserted through the  
Backrest Bracket (9).  
Adjustment Hole  
ADJUSTING THE WEIGHT REST AND WEIGHT  
SPOTTER  
4
12  
18  
18  
Before beginning an exercise, move the Weight  
Rests (12) and the Weight Spotters (11) to sets of  
holes in the Uprights (4) that are best suited for that  
exercise. Do this by turning the Adjustment Knobs  
(18) counterclockwise until loose. Pull the Knobs out  
and slide the Weight Rests or the Weight Spotters to  
the desired height. Snap the Knobs into the adjust-  
ment holes in the Uprights and turn the Knobs clock-  
wise until tight.  
11  
Adjustment Hole  
The selected holes for the Weight Spotters (11)  
should represent the lowest point to which you want  
the barbell to go during the exercise. The selected  
holes for the Weight Rests (12) should be at a com-  
fortable height for lifting and replacing the barbell.  
Perform the exercise as shown on the accompanying  
exercise guide. Note: Make sure the Adjustment  
Knobs (18) are fully tightened.  
WARNING:Always set both Weight  
Rests (12) at the same height and both Weight  
Spotters (11) at the same height.  
10  
 
EXERCISE GUIDELINES  
THE FOUR BASIC TYPES OF WORKOUTS  
PERSONALIZING YOUR EXERCISE PROGRAM  
Muscle Building  
To increase the size and strength of your muscles,  
Determining the exact length of time for each workout,  
as well as the number of repetitions or sets completed,  
push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo-  
cles will continually adapt and grow as you progres-  
sively increase the intensity of your exercise. You can  
adjust the intensity level of an individual exercise in  
two ways:  
• by changing the amount of weight used  
• by changing the number of repetitions or sets per-  
formed. (A “repetition” is one complete cycle of an  
exercise, such as one sit-up. A “set” is a series of  
repetitions.)  
ing it during the first few months of your exercise pro-  
gram. You should progress at your own pace and be  
sensitive to your body’s signals. If you experience pain  
or dizziness at any time while exercising, stop immedi-  
ately and begin cooling down. Find out what is wrong  
before continuing. Remember that adequate rest and a  
proper diet are important factors in any exercise pro-  
gram.  
WARMING UP  
The proper amount of weight for each exercise  
depends upon the individual user. You must gauge  
Begin each workout with 5 to 10 minutes of stretching  
your limits and select the amount of weight that is right and light exercise to warm up. Warming up prepares  
for you. Begin with 3 sets of 8 repetitions for each  
exercise you perform. Rest for 3 minutes after each  
set. When you can complete 3 sets of 12 repetitions  
without difficulty, increase the amount of weight.  
your body for more strenuous exercise by increasing  
circulation, raising your body temperature and deliver-  
ing more oxygen to your muscles.  
WORKING OUT  
Toning  
You can tone your muscles by pushing them to a mod- Each workout should include 6 to 10 different exercis-  
erate percentage of their capacity. Select a moderate  
amount of weight and increase the number of repeti-  
tions in each set. Complete as many sets of 15 to 20  
repetitions as possible without discomfort. Rest for 1  
minute after each set. Work your muscles by complet-  
ing more sets rather than by using high amounts of  
weight.  
es. Select exercises for every major muscle group,  
emphasizing areas that you want to develop most. To  
give balance and variety to your workouts, vary the  
exercises from session to session.  
Schedule your workouts for the time of day when your  
energy level is the highest. Each workout should be  
followed by at least one day of rest. Once you find the  
schedule that is right for you, stick with it.  
Weight Loss  
To lose weight, use a low amount of weight and  
increase the number of repetitions in each set.  
Exercise for 20 to 30 minutes, resting for a maximum  
of 30 seconds between sets.  
EXERCISE FORM  
Maintaining proper form is an essential part of an  
effective exercise program. This requires moving  
through the full range of motion for each exercise, and  
Cross Training  
Cross training is an efficient way to get a complete and moving only the appropriate parts of the body.  
well-balanced fitness program. An example of a bal-  
anced program is:  
• Plan weight training workouts on Monday,  
Wednesday, and Friday.  
• Plan 20 to 30 minutes of aerobic exercise, such as  
cycling or swimming, on Tuesday and Thursday.  
• Rest from both weight training and aerobic exercise  
for at least one full day each week to give your body  
time to regenerate.  
Exercising in an uncontrolled manner will leave you  
feeling exhausted. On the exercise guide accompany-  
ing this manual you will find photographs showing the  
correct form for several exercises, and a list of the  
muscles affected. Refer to the muscle chart on page  
12 to find the names of the muscles.  
The repetitions in each set should be performed  
smoothly and without pausing. The exertion stage of  
each repetition should last about half as long as the  
return stage. Proper breathing is important. Exhale  
The combination of weight training and aerobic exer-  
cise will reshape and strengthen your body, plus devel- during the exertion stage of each repetition and inhale  
op your heart and lungs. during the return stroke. Never hold your breath.  
11  
 
Rest for a short period of time after each set. The  
ideal resting periods are:  
• Rest for three minutes after each set for a muscle  
building workout.  
slowly as you stretch and do not bounce. Ease into  
each stretch gradually and go only as far as you can  
without strain. Stretching at the end of each workout  
is an effective way to increase flexibility.  
• Rest for one minute after each set for a toning work-  
out.  
STAYING MOTIVATED  
• Rest for 30 seconds after each set for a weight loss  
workout.  
Plan to spend the first couple of weeks familiarizing  
yourself with the equipment and learning the proper  
form for each exercise.  
For motivation, keep a record of each workout. The  
chart on page 13 of this manual can be photocopied  
and used to schedule and record your workouts. List  
the date, the exercises performed, the weight used,  
and the numbers of sets and repetitions completed.  
Record your weight and key body measurements at  
the end of every month. Remember, the key to  
achieving the greatest results is to make exercise a  
regular and enjoyable part of your everyday life.  
COOLING DOWN  
End each workout with 5 to 10 minutes of stretching.  
Include stretches for both your arms and legs. Move  
MUSCLE CHART  
N
O
P
A. Sternomastoid (neck)  
B. Pectoralis Major (chest)  
C. Biceps (front of arm)  
D. Obliques (waist)  
A
B
E. Brachioradials (forearm)  
F. Hip Flexors (upper thigh)  
G. Abductor (outer thigh)  
H. Quadriceps (front of thigh)  
I. Sartorius (front of thigh)  
J. Tibialis Anterior (front of calf)  
K. Soleus (front of calf)  
C
D
E
Q
R
S
F
L
T
L. Rectus Abdominus (stomach)  
M. Adductor (inner thigh)  
G
M
N. Trapezius (upper back)  
O. Rhomboideus (upper back)  
P. Deltoid (shoulder)  
H
I
U
V
Q. Triceps (back of arm)  
J
K
W
R. Latissimus Dorsi (mid back)  
S. Spinae Erectors (lower back)  
T. Gluteus Medius (hip)  
U. Gluteus Maximus (buttocks)  
V. Hamstring (back of leg)  
W. Gastrocnemius (back of calf)  
12  
 
MONDAY  
Date:  
/
EXERCISE  
WEIGHT  
WEIGHT  
WEIGHT  
SETS  
SETS  
SETS  
REPS  
REPS  
REPS  
/
AEROBIC EXERCISE  
EXERCISE  
TUESDAY  
Date:  
/
/
WEDNESDAY  
Date:  
/
/
AEROBIC EXERCISE  
EXERCISE  
THURSDAY  
Date:  
/
/
FRIDAY  
Date:  
/
/
Make photocopies of this page for scheduling and recording your workouts.  
13  
 
PART LIST—Model No. WEBE15210  
R1001A  
Key No. Qty.  
Description  
Key No. Qty.  
Description  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
1
1
1
2
2
1
1
1
1
2
2
2
1
1
1
8
2
4
5
5
4
5
4
4
Frame  
Front Stabilizer  
Crossbar  
Upright  
Upright Stabilizer  
Seat Frame  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
#
2
2
4
2
1
Pad Tube  
Plastic Plate  
M10 Washer  
M10 x 78mm Bolt  
Small Adjustment Knob  
Backrest Adjustment Knob  
M6 x 16mm Bolt  
8mm Bushing  
12.5mm Spacer  
M10 x 95mm Bolt  
M10 Nylon Locknut  
M10 x 65mm Bolt  
M10 x 140mm Bolt  
M10 x 100mm Bolt  
M6 x 50mm Bolt  
M8 x 55mm Carriage Bolt  
M10 x 65mm Carriage Bolt  
M8 Nylon Locknut  
20mm x 40mm Inner Cap  
50mm Round Inner Cap  
40mm x 50mm Inner Cap  
User’s Manual  
1
2
Seat  
Backrest  
10  
2
10  
21  
2
2
1
5
4
4
4
4
1
1
1
1
Backrest Bracket  
Backrest Frame  
Weight Spotter  
Weight Rest  
Leg Lever Bracket  
Seat Bracket  
Leg Lever  
Square Bushing  
Upright Cap  
Large Adjustment Knob  
M6 Washer  
75mm x 50mm Inner Cap  
Support Plate  
50mm Square Inner Cap  
Foam Pad  
#
Exercise Guide  
19mm Round Inner Cap  
“#” Indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover for  
information on ordering replacement parts.  
14  
 
EXPLODED DRAWING—Model No. WEBE15210  
R1001A  
16  
18  
8
12  
16  
40  
18  
43  
11  
10  
16  
32  
27  
10  
16  
12  
16  
19  
39  
27  
32  
17  
18  
43  
19  
9
7
39  
11  
42  
35 33  
32  
42  
45  
33  
26  
35  
18  
32  
16  
17  
6
37  
13  
32  
32  
34  
31  
35  
30  
4
35  
29  
19  
39  
35  
14  
28  
20  
35  
21  
35  
32  
28  
35  
4
1
34  
35  
35  
37  
32  
2
21  
34  
20  
22  
21  
38  
34  
35  
3
5
35  
35  
20  
27  
36  
22  
22  
34  
21  
24  
41  
23  
20  
15  
5
20  
25  
22  
41  
44  
22  
24  
23  
15  
 
ORDERING REPLACEMENT PARTS  
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday  
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-  
pared to give the following information when calling:  
1. The MODEL NUMBER of the product (WEBE15210)  
2. The NAME of the product (WEIDER® PRO 425 weight bench)  
3. The SERIAL NUMBER of the product (see the front cover of this manual)  
4. The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED  
DRAWING on pages 14 and 15).  
LIMITED WARRANTY  
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-  
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This  
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing  
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which war-  
ranty claim is made must be received by ICON at one of its authorized service centers with all freight and other  
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-autho-  
rized by ICON. This warranty does not extend to any product or damage to a product caused by or attribut-  
able to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON  
authorized service center, products used for commercial or rental purposes, or products used as store display  
models. No other warranty beyond that specifically set forth above is authorized by ICON.  
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection  
with the use or performance of the product or damages with respect to any economic loss, loss of property,  
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-  
ages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequen-  
tial damages. Accordingly, the above limitation may not apply to you.  
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-  
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.  
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation  
may not apply to you.  
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.  
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813  
Part No. 177215 R1001A  
Printed in China © 2001 ICON Health & Fitness, Inc.  
 

Weslo Treadmill WLTL48590 User Manual
Whirlpool Dishwasher WDF310PAAW User Manual
Whirlpool Range W10200946A User Manual
Whirlpool Ventilation Hood Ventilation Hood User Manual
Whirlpool Washer 3950952REVB User Manual
Whirlpool Washer Dryer BYCWD6274W3 User Manual
Xilinx Network Card 1000BASE X User Manual
Yamaha CD Player CRW8824E User Manual
Zanussi Clothes Dryer TD150 A User Manual
Zenoah Trimmer CHTZ6010 User Manual