Yahee Refrigerator RETRT2812 1 User Manual

Operating Manual  
USER'S INSTRUCTIONS  
Model No.: RETRT2812-1  
(DC 12V  
/AC 24V ~ 60HZ, 12W / NTSC)  
REVO AMERICA  
700 FREEPORT PARKWAY SUITE 100 COPPELL,  
TX 75019 U.S.A. TEL.: 1-866-625-REVO(7386)  
 
USER’S MANUAL  
Contents  
General Features  
4
5
6
7
Installing & Adjusting  
Dimension & Specification  
OSD Control Button  
Camera Menu Set Up  
1
.
.
.
.
.
.
.
.
.
.
Menu Set Up  
8
2
Lens Setting  
8
3
Exposure Setting  
White Balance Setting  
SSDR Setting  
9
4
10  
11  
12  
13  
14  
15  
19  
20  
5
6
Backlight Setting  
DNR3 Setting  
7
8
Day/Night Setting  
Special Setting  
Exit Setting  
9
10  
Trouble Shooting  
3
 
USER’S MANUAL  
General Features  
Ultra High Sensitivity  
- The built-in high sensitivity COLOR CCD produces a clear image even in 0Lux(B/W, IR-LED ON)  
or lower illumination.  
600TV Lines  
- By adopting a diagonal 2.8mm(1/3") 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD,  
the camera produces clear picture quality with a horizontal resolution of 600 TV lines for  
color and a horizontal resolution of 700TV lines for BW mode.  
DNR3  
-
The high-performance W-V DSP chip effectively removes low-light gain noise and  
ghosting to  
provide clear images even in dark environments.  
Day & Night  
- This camera has a function that automatically selects the mode that is appropriate for  
daytime or night-time conditions. The COLOR mode operates in daytime conditions to  
provide optimum colors, and BW mode operates in night-time conditions to enhance the  
definition of the image.  
SSDR  
- For images with high contrast between bright and dark Areas from difficult lighting conditions  
such as backlighting, this camera selectively illuminates darker Areas while retaining the same  
light level for brighter Areas to even out the overall brightness.  
Miscellaneous Functions  
- HLC(High Light Compensation), SENS-UP, FLIP(H/V-REV), D-ZOOM, SHARPNESS, MOTION  
DETECTION and PRIVACY functions are provided.  
Disk Saving Effects  
- Up-most and advanced DNR technology camera picture quality has a disk saving effects due  
to  
Image sizes are smaller than standard CCTV camera image.  
Controlled by OSD Menu  
- The camera can be controlled by selecting the menu text displayed on the monitor screen.  
IP66 Approved / Vandal Proof / RoHS Compliance  
- To prevent from external strong impact  
.
It has a high strength and durable exterior material of die  
cast aluminum body It also has designed to prevent from shock, dust and rain resistant. The  
.
turret camera has designed to install anywhere even at exterior places.  
4
 
USER’S MANUAL  
INSTALLING & ADJUSTING  
1.  
Installation  
- Place the mounting plate on a flat installation surface  
and mount with the provided screws.  
- Feed the cable through the center of the mounting plate.  
- Place the camera body in the mounting plate socket  
and hold.  
- Then place the outer plate over the camera body &  
mounting plate and tighten side screws to lock the  
camera into place.  
- Loosen side screws to adjust camera angle as needed,  
then tighten the side screws to lock into place.  
2.  
Focus/Zoom Screw  
- To widen the viewing angle turn the Zoom screw  
to "W"(Wide) to obtain a closer view turn it to  
"T"(Tele)  
- Turn the Focus screw to "N"(Near) or "  
(Far) until the sharpest Focus is made.  
"
5
 
USER’S MANUAL  
DIMENSION & SPECIFICATION  
1. Dimension & Connection  
Dimension  
Connection  
140mm  
2.  
Specification  
Image Pick-Up Device  
TV System  
1/3” Sony Super HAD CCD  
NTSC  
Total Pixels  
811(H) * 508(V)  
768(H) * 494(V)  
Scanning Frequency  
Scanning System  
Synchronization  
Resolution  
15.734KHz(H) & 59.94Hz(V)  
2:1 Interlace  
Internal / Line Lock  
600TV Lines  
Minimum Illumination  
S/N Ratio  
IR LED OFF: 0.15 Lux, IR LED ON: 0.00002 Lux  
More than 52dB  
VideoOutput  
Electronic Shutter Speed  
OSD  
CVBS: 1.0Vp-p / 75  
NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec)  
Available  
SSDR  
On / O Level adjustable)  
BLC / HLC / OFF  
BLC  
Day & Night  
Color / BW / AUTO  
Gain Control  
Low / High /  
White Balance  
SENS-UP  
ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)  
Auto / O Selectable x2 ~ x512)  
Motion Detection  
Privacy Masking  
DNR3(DigitalNoiseReduction)  
Digital Zoom  
DIS (Digital ImageStabilization)  
Sharpness  
On / O  
On / O  
Programmable Zones)  
Programmable Zones)  
On / O Level adjustable)  
On / O x1 ~ x16)  
On /  
On / O Level adjustable)  
Flip / Mirror  
On /  
Power Supply  
Power Consumption  
Lens  
DC 12V / AC 24V Dual Voltage  
IR LED OFF 200mA(DC), IR LED OFF 70mA(AC) / IR LED ON 670mA(DC), IR LED ON 240mA(AC)  
DC Auto Iris Varifocal Lens(2.8mm-12mm)  
Operational Temp  
.
-10 ~ +50 Deg C  
-20 ~ +60 Deg C  
.
.
RH95% MAX.  
RH95% MAX.  
Storage Temp  
.
Dimension  
Weight  
140mm(W) * 111mm(H) * 180mm(D)  
1800g  
6
 
USER’S MANUAL  
OSD Control Button  
1.  
OSD button could be used when it needs to OSD control.  
Up button: Moves the cursor upwards  
or adjust the parameters.  
.
Use this button to select an item  
Down button: Moves the cursor downwards  
item or adjust the parameters.  
.
Use this button to select an  
Left button: Moves the cursor to the left  
.
Use this button to select or  
adjust the parameters of the selected item  
.
The parameter changes  
each time this button is pressed.  
Right button: Moves the cursor to the right  
.
Use this button to select or  
The parameter changes each  
adjust the parameters of the selected item  
.
time this button is pressed.  
Set button: Executes selections and displays a submenu for an item with  
the mark.  
7
 
USER’S MANUAL  
Menu Setup  
1
.
Press the Function Setup switch.  
- Main setup menu is displayed on the monitor screen.  
MA N SETUP  
1 LENS  
DC  
2 EXPOSURE  
3 WH TE BAL  
ATW  
OFF  
OFF  
ON  
.
4 SSDR  
5 BACKL GHT  
6 DNR3  
7 DAY/N GHT  
8 SPEC AL  
9 EX T  
AUTO  
SAVE  
2
.
Select a desired function using the Function Setup switch.  
- Place the cursor over a desired item.  
3
4
.
Set up a selected item by using the Function Setup switch.  
. To finish the setting, select 'EXIT' and press the Function Setup switch.  
NOTE  
An item with theicon also has sub menus. To select a sub menu, select an item  
with the icon and press the Function Setup switch.  
An item with the - - - icon is unavailable due to function settings.  
Lens Setting  
Using this function, you can control the screen brightness.  
1
2
.
When the SETUP menu screen is displayed, select 'LENS' by using  
the Function Setup switch so that the arrow indicates 'LENS'.  
DC: You can adjust the minimum shutter and maximum value of ESC  
shutter mode.  
.
MA N SETUP  
1 LENS  
DC  
2 EXPOSURE  
3 WH TE BAL  
ATW  
3
.
THE Lens mode has sub menu items as listed below.  
- BRIGHTNESS: Adjusts the video brightness.  
8
 
USER’S MANUAL  
- FOCUS ADJ: To adjust the DC lens focus correctly, you must activate the Focus Settings  
mode under each lens menu Activate the Focus Settings mode, adjust the lens focus, and  
.
then deactivate the settings mode.  
NOTE  
If color rolling occurs when using a DC lens, set Shutter to Fixed (---).  
Exposure Setting  
MA N SETUP  
1 LENS  
DC  
2 EXPOSURE  
3 WH TE BAL  
ATW  
1
.
When the SETUP menu screen is displayed, select 'EXPOSURE' by using the  
Function Setup Switch.  
2
.
Select a desired mode using the Function Setup switch.  
EXPOSURE SETUP  
1 BR GHTNESS  
2 SHUTTER  
3 AGC  
25  
-
-
-
H GH  
OFF  
-
4 SENS UP  
5 RETURN  
SHUTTER: You can select either auto or manual shutter.  
* --- : Shutter speed is fixed at 1/60sec(1/50sec)  
* ESC: Select this to control the shutter speed automatically  
.
If ESC is selected, the shutter  
speed is automatically controlled depending on the ambient illumination of the subject.  
* MANUAL: You can control shutter speed manually.  
(NTSC MODEL:1/60~1/120,000, PAL MODEL:1/50~1/120,000)  
* A.FLK : Select this when you see picture flicker, this can happen when the frequency of the  
local lighting clashes with the camera.  
NOTE  
When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.  
9
 
USER’S MANUAL  
AGC (AUTO GAIN CONTROL): The higher the gain level, the brighter the screen  
but the higher the noise.  
* OFF: Deactivates the AGC function.  
* LOW:Allows automatic gain control from 5.3dB to 32dB.  
* HIGH:Allows automatic gain control from 5.3dB to 37dB.  
SENS-UP: When it is night or dark, the camera automatically detects the light  
level and maintains a clear picture if this mode is activated.  
* OFF: Deactivates the SENS-UP function.  
* AUTO:Activates the SENS-UP function.  
RETURN: Select this to save the changes in the EXPOSURE menu and  
return to the SETUP menu.  
NOTE  
If you press the Function Setup switch to ‘AUTO’ mode, you can adjust  
brightness by  
increasing or decreasing the shutter speed (x2 ~ x512)  
.
Note that the higher the zoom level, the brighter the screen, but the more likely  
there will be a ghosting effect.  
It is normal for Noise, Spots and Whitish symptoms to appear in SENS-UP mode  
when the D-ZOOM level is increased.  
White Balance (White Bal) Setting  
Use the White Balance function to adjust the screen color.  
1.  
When the SETUP menu screen is displayed, select 'White Bal' by using the Function  
Setup switch so that the arrow indicates 'White Bal'.  
2.  
Select a desired mode using the Function Setup switch.  
MA N SETUP  
1 LENS  
DC  
2 EXPOSURE  
3 WH TE BAL  
ATW  
10  
 
USER’S MANUAL  
Select one of the following 5 modes, as appropriate for your  
purpose.  
ATW: Select this when the color temperature is between 1,700˚K  
and 11,000˚K.  
OUTDOOR:Select this when the color temperature is between 1,700˚K and 11,000˚K.  
(sodium light inclusion)  
INDOOR:Select this when the color temperature is between 4,500˚K and 8,500˚K.  
MANUAL: Select this to fine-tune White Balance manually  
.
Set White Balance first by using the  
ATW or AWC mode After that switch to MANUAL mode, fine-tune the White Balance and then  
.
press the Function Setup switch.  
AWCSET:To find the optimal luminance level for the current environment, point the  
camera towards a sheet of white paper and press the Function Setup switch  
changes, readjust it.  
.
If the environment  
NOTE  
White Balance may not work properly under the following conditions  
select the AWC mode.  
when the color temperature of the environment surrounding the subject is out of the  
.
In this case  
control range (e.g clear sky or sunset).  
.
when the ambient illumination of the subject is dim.  
If the camera is directed towards a fluorescent light or is installed in a place where  
illumination changes dramatically, the White Balance operation may become unstable.  
SSDR Setting  
SSDR illuminates darker spots of an image while retaining the same light level for brighter  
spots to even out the overall brightness of images with high contrast between bright and  
dark spots.  
MA N SETUP  
1 LENS  
DC  
2 EXPOSURE  
3 WH TE BAL  
ATW  
OFF  
.
4 SSDR  
1
.
When the SETUP menu screen is displayed, select 'SSDR' by using the switch so  
that the arrow indicates 'SSDR'.  
Use the switch to change the SSDR level according to the contrast between bright  
and dark areas.  
2
.
 
USER’S MANUAL  
Backlight Setting  
Unlike conventional cameras, W-V chip camera is designed to deliver a distinctive subject  
and background at the same time, even when the subject is backlight, by using the features  
of the proprietary W-V DSP chip.  
1.  
When the SETUP menu screen is displayed, select 'BACKLIGHT' by using the Function  
Setup switch so that the arrow indicates 'BACKLIGHT'.  
MA N SETUP  
1 LENS  
DC  
2 EXPOSURE  
3 WH TE BAL  
ATW  
OFF  
OFF  
ON  
.
4 SSDR  
5 BACKL GHT  
6 DNR3  
7 DAY/N GHT  
8 SPEC AL  
9 EX T  
AUTO  
SAVE  
2
.
Select a desired mode using the Function Setup switch.  
BLC : Enables a user to directly select a desired area from a picture, and to view  
the area more clearly.  
HLC (High Light Compensation) : If the scene contains extremely bright light areas  
such as; from car headlights, the light can mask out much of the on-screen detail  
- LEVEL :Adjust level of the HLC function.  
- LIMIT:Enable to change the operating condition.  
- MASK COLOR/TONE: Change the color / transparency of the masking area.  
(Black, Red, Blue, Cyan, Magenta)  
- TOP/BOTTOM/LEFT/RIGHT: Adjust the area to be enhanced  
OFF: Not being used  
3.  
Select a desired mode using the Function Setup switch and press the Function Setup switch.  
Select 'BLC' to adjust the area to be  
enhanced then adjust the level  
Select 'HLC' to adjust the area to be  
enhanced then adjust the level.  
.
 
USER’S MANUAL  
USER’S MANUAL  
HLC SETUP  
BLC SETUP  
LEVEL  
T
LOW  
38  
M DDLE  
N GHT ONLY  
LEVEL  
L M TS  
BOTTOM  
LEFT  
R GHT  
109  
54  
121  
MASK COLOR  
MASK TONE  
TOP  
BLACK  
1
5
BOTTOM  
LEFT  
120  
5
Press Set to Return  
R GHT  
172  
Press Set to Return  
NOTE  
Because there can be a difference in the effectiveness of HLC according to the amount  
of light area in the screen, optimize the installation angle for the best HLC performance.  
When dark, the HLC is only activated when a bright light exceeding a specific size in  
NIGHT ONLY mode.  
The HLC is not activated in day light or when bright light is not present at night in NIGHT  
ONLY mode.  
BLC Function doesn't work in the B/W mode of the DAY/NIGHT menu.  
DNR3 Setting  
This function reduces the background noise in a low luminance environment.  
1.  
When the SETUP menu screen is displayed, select 'DNR3' by using the Function  
Setup switch so that the arrow indicates 'DNR3'.  
MA N SETUP  
1 LENS  
DC  
2 EXPOSURE  
3 WH TE BAL  
4.SSDR  
5 BACKL GHT  
6 DNR3  
ATW  
OFF  
OFF  
ON  
AUTO  
7 DAY/N GHT  
8 SPEC AL  
9 EX T  
SAVE  
2
.
Select a desired mode using the Function Setup switch.  
OFF: Deactivates DNR3 Noise is not reduced.  
ON: Activates DNR3 so that noise is reduced.  
.
 
USER’S MANUAL  
3
.
Set the DNR3 mode to 'ON' and press the Function Setup switch  
.
Then you  
can adjust the noise reduction level.  
NOTE  
You cannot set the DNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’.  
When adjusting the noise reduction level in the DNR3 mode, remember that the higher the  
level set, the more the noise level will be reduced, as will the brightness of the image.  
Day/Night Setting  
You can display pictures in color or black and white.  
1
.
When the SETUP menu screen is displayed, select 'DAY/NIGHT 'by using the  
Function Setup switch so that the arrow indicates 'DAY/NIGHT'.  
MA N SETUP  
1 LENS  
DC  
2 EXPOSURE  
3 WH TE BAL  
4.SSDR  
5 BACKL GHT  
6 DNR3  
ATW  
OFF  
OFF  
ON  
AUTO  
7 DAY/N GHT  
8 SPEC AL  
9 EX T  
SAVE  
2
.
Select a desired mode using the Function Setup Switch according to the picture  
display you want.  
COLOR: The picture is always displayed in color.  
B/W: The picture is always displayed in black and white.  
- BURST MODE: You can turn on or off the burst signal on B/W mode.  
B/W MODE SETUP  
1 BURST MODE  
RETURN  
ON  
.
2
14  
 
USER’S MANUAL  
AUTO:The mode is switched to 'Color' in a normal environment, but switches to 'B/W' mode  
when ambient illumination is low  
.
To set up the switching time for AUTO mode, press the  
Function Setup switch You can turn on or off the burst signal on B/W mode.  
.
- BURST MODE:You can turn on or off the burst signal  
on B/W mode.  
AUTO SETUP  
ON  
1 BURST MODE  
-DURATION:You can select brightness of illumination  
about changing the day/night mode.  
2 COLORB/W  
DURAT ON  
DWELL T ME  
3 B/WCOLOR  
DURAT ON  
FAST  
3SEC  
- DWELLTIME:You can select the duration time about  
changing the day/night mode.  
FAST  
10SEC  
DWELL T ME  
4 RETURN  
3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s  
COLORB/W  
2.5 lux  
B/WCOLOR  
5 lux  
FAST  
SLOW  
* The day/night switching point of the  
camera can be adjusted.  
10 lux  
1 lux  
NOTE  
When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR'  
mode and 'AUTO' mode cannot be selected.  
Special Setting  
1
.
When the SETUP menu screen is displayed, select 'SPECIAL' by using the Function Setup  
switch so that the arrow indicates 'SPECIAL'.  
MA N SETUP  
1 LENS  
DC  
2 EXPOSURE  
3 WH TE BAL  
4.SSDR  
5 BACKL GHT  
6 DNR3  
ATW  
OFF  
OFF  
ON  
AUTO  
7 DAY/N GHT  
8 SPEC AL  
9 EX T  
SAVE  
15  
 
USER’S MANUAL  
2
.
Select a desired mode using the Function Setup switch.  
SPEC AL  
1 MAGE ADJ  
.
2 MON TOR  
LCD  
OFF  
3
.
CAM T TLE  
NT  
.
4 SYNC  
OFF  
.
5 MOT ON DET  
OFF  
.
6 PR VACY  
ENGL SH  
.
7 LANGUAGE  
.
9 RETRUN  
IMAGEADJ.:  
1) When the SETUP menu screen is displayed, select 'IMAGE ADJ' by using the  
Function Setup switch so that the arrow indicates 'IMAGE ADJ'.  
2) Select a desired mode using the Function Setup switch.  
MAGE SETUP  
1 V REV  
-
2 H  
3 D  
-
-
REV  
ZOOM  
OFF  
OFF  
.
4 D S  
OFF  
.
5 FONT COLOR  
WH TE  
ON  
.
6 SHARPNESS  
.
7 RETURN  
* V-REV:You can flip the picture vertically on the screen.  
* H-REV:You can flip the picture horizontally on the screen. *  
* D-ZOOM: You can use a digital zoom of x1 ~ x16.  
* FONT COLOR:You can change the OSD font color (White, Yellow, Green, Red, Blue)  
.
* SHARPNESS:As you increase this value, the picture outline becomes stronger and clearer.  
Adjust this value appropriately depending on the sharpness of the picture.  
* DIS (Digital Image Stabilizer):  
This function mitigates any picture movement due to external factors such as wind.  
NOTE  
As the DIS function uses the digital zoom the camera's resolution will decrease.  
DIS doesn’t operate when background illumination is too low.  
DIS doesn’t operate when object pattern is monotonic as like sky or white wall.  
* RETURN: Select this to save the settings for the IMAGE ADJ menu and to return to the SETUP  
menu.  
16  
 
USER’S MANUAL  
NOTE  
When the V-REV or H-REV mode is enabled, the text on the screen does not flip.  
If you increase the SHARPNESS level too high, the picture may become distorted or noise  
may appear.  
CAM TITLE: If you enter a title, the title will appear on the monitor.  
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the  
arrow indicates 'CAM TITLE'.  
CAMERA T TLE SETUP  
2) Set it to 'ON' by using the Function Setup switch.  
A B C D E F G H J K L M  
3) Press the Function Setup switch.  
N O P Q R S T U V W X Y Z  
4) Use the Function Setup switch to move to a  
desired letter and select the letter by pressing  
l
a b c d e f g h i j k  
m
n o p q r s t u v w x y z  
.
-
0 1 2 3 4 5 6 7 8 9  
the Function Setup switch  
.
Repeat this to enter  
←→CLR  
POS  
END  
multiple letters You can enter up to 15 letters.  
.
5) Enter a title, move the cursor to 'POS' and  
press the Function Setup switch The entered  
title appears on the screen Select the position  
SHOP  
.
.
to display the title on the screen by using the  
Function Setup switch and press the Function  
Setup switch When the position is determined,  
.
select 'END' and press the Function Setup switch  
to return to the SPECIAL menu.  
NOTE  
When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if  
you enter one.  
Only English is available in this mode.  
If you move the cursor to CLR and press the Function Setup switch, all the letters are  
deleted  
Setup switch  
.
To edit a letter, change the cursor to the bottom left arrow and press the Function  
Move the cursor over the letter to be edited, move the cursor to the letter to be  
.
inserted and then press the Function Setup switch.  
SYNC : In areas where the supply is at 60Hz(NTSC), 50Hz(PAL), you can synchronize the  
output phase of multiple cameras using the power synchronization function (Line-Lock)  
without using a synchronization signal generator.  
- INT: Internal Synchronization Type  
-L/L: Power Synchronization Type, Line-lock(AC24V Power)  
* Press the Function Setup switch.  
* You can select a desired phase from 0 to 359 when select 'phase'.  
17  
 
USER’S MANUAL  
NOTE  
When using AC power at 60Hz(NTSC), 50Hz(PAL), frequency, you can use the L/L type  
synchronization.  
When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.  
MOTION DET :This product has a feature that  
MOT ON DET  
allows you to observe movement of objects in  
.
1 SENS T V TY  
AREA1  
ON  
8
different areas on the screen, and the  
.
2 AREA MODE  
words  
.
'MOTION DETECTED' appear on the  
screen when  
-
3 SEL POS  
L TOP  
.
4 XPOS  
3
5
movement is detected.  
.
5 YPOS  
Activity can be monitor more efficiently.  
.
6 F LL SET  
.
7 RETRUN  
1) When the SPECIAL menu screen is displayed,  
press the Function Setup switch so that the arrow  
indicates 'MOTION DET’.  
2) Set up the mode using the Function Setup switch.  
- SENSITIVITY:You can select up to 8 MD areas When SENSITIVITY number is high, motion  
.
detection sensitivity is increased to recognize even small movement.  
- AREA MODE: Determines whether to use the MD area selected in SENSITIVITY.  
- SEL POS: Determines which of the 4 vertices of each MD area is to be used.  
- XPOS: Determines the coordinate of the horizontal axis for SEL POS.  
- YPOS:Determines the coordinate of the vertical axis for SEL POS.  
-
FILLSET: Fills in a selected MD area  
blue, cyan, green, yellow, magenta and red.  
- RETURN:Select this to save the MOTION DET menu settings and return to the SPECIAL menu.  
.
The color of the area can be selected from brown, orange,  
PRIVACY: Mask an area you want to hide on the screen.  
PR VACY AREA SETUP  
1 AREA  
2 MODE  
3 MASK COLOR  
4 MASK TONE  
5 TOP  
AREA1  
OFF  
GREEN  
1
39  
6 BOTTOM  
7 LEFT  
79  
13  
8 R GHT  
52  
9 RETURN  
18  
 
USER’S MANUAL  
1) When the SPECIAL menu screen is displayed, press the Function Setup switch so  
that the arrow indicates 'PRIVACY'.  
2) Set up the mode using the Function Setup switch.  
-AREA:You can select up to 12 PRIVACY areas.  
- MODE:Determines whether to use the area selected in theAREA.  
- MASK COLOR:Determine area color You can select Green, Red, Blue, Black, White, Gray.  
.
- MASK TONE:Adjust the brightness of MASK COLOR.  
- TOP/BOTTOM/LEFT/RIGHT:Adjustthe size and position of the selected area.  
- RETURN:Select this to save the PRIVACYmenu settings andreturn to theSPECIALmenu.  
MONITOR :  
Please change the settings value of video appropriate to your monitor.  
- LCD: Please select this menu item when using a LCD monitor.  
- CRT:Please select this menu item when using a CRT monitor.  
- USER:Please use this menu item when using a monitor other than standard ones  
Change the gamma, PED level, and color gain in the sub menus.  
.
You can  
LANGUAGE: You can select the menu language according to your requirements.  
RETURN:Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu.  
Exit Setting  
Select a desired EXIT mode using the Function Setup Switch.  
- SAVE: Save the current settings and exit the MAIN SETUP menu.  
- NOT SAVE: Do not save the current settings and exit the MAIN SETUP menu.  
- RESET: Resets the camera settings to the factory defaults  
Monitor Settings are not initialized.  
.
Language, Communication and  
19  
 
USER’S MANUAL  
Trouble Shooting  
PROBLEM  
POSSIBLE CAUSE  
Check the power cable, power supply output and video  
connection between the camera and monitor.  
Northing appears on  
the screen.  
Are the camera lens or the lens glass dirty?  
Clean the lens / glass with a soft clean cloth.  
Adjust the monitor controls, as required.  
If the camera is facing a very strong light, change  
the camera position.  
The image on the  
screen is dim.  
Adjust the lens focus  
Adjust the contrast control of the monitor.  
The image on the  
screen is dark.  
If there is an intermediate device, correctly set the 75/Hi-z.  
Check the camera is correctly connected to an appropriate  
regulated power source.  
The camera is not  
working properly  
and the surface of  
the camera is hot.  
Has MOTION DET been set to ON in the menu?  
Has MD AREA been properly defined?  
Motion Detection  
is not activated.  
The color of the  
Check the settings in WHITE BALANCE menu.  
picture is not correct.  
Make sure that the camera isn’t facing direct sunlight or  
The image on the  
screen flickers.  
Fluorescent lighting If necessary, change the camera position.  
.
Check that theAGC setting in the EXPOSURE menu isn't set to OFF.  
Check the EXPOSURE menu and make sure SHUTTER is set to------.  
The SENS-UP does  
not work.  
20  
 
USER’S MANUAL  
21  
 
 

Weider Home Gym WESY75742 User Manual
Weil McLain Burner RLS User Manual
Weslo Treadmill PFT80 User Manual
Westinghouse Power Hammer IL33 856 2 User Manual
Xantech Stereo Receiver 291 80 User Manual
Xantrex Technology Battery Charger SW 3000 User Manual
Yamaha Guitar 120S User Manual
Zanussi Freezer ZU 9120 F User Manual
Zebra Technologies All in One Printer ZD500 User Manual
Zenoah Trimmer KAM 402 User Manual